Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D3291-11(2016)e1
Standard Practice for Compatibility of Plasticizers in Poly(Vinyl Chloride) Plastics Under Compression (Includes all amendments And changes 5/25/2022).
NORMA vydaná dňa 1.9.2016
Informácie o norme:
Označenie normy: ASTM D3291-11(2016)e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2016
Kód tovaru: NS-667141
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D3291-11(2016)e1 :
Keywords:
plasticizer compatibility, plasticizers, poly(vinyl chloride),, ICS Number Code 83.040.30 (Auxiliary materials and additives for plastics)
Doplňujúce informácie
| Significance and Use | ||||
|
5.1 It is possible for plasticizers to become less compatible in poly(vinyl chloride) resin when fused compound is subjected to compressive stress. 5.1.1 This test subjects a standard test specimen to a definite deformation and allows qualitative determination of the amount of spew that is capable of occurring over a period of time. 5.1.2 An apparent decrease in compatibility of plasticizers with subsequent exudation can cause excessive dirt pickup, marring of lacquered or varnished surfaces, sticky feel, and a number of other associated problems. 5.1.3 When a plasticized poly(vinyl chloride) sheet is stressed in compression by bending it through 180°, one way to relieve the stress is by migration of the plasticizer from the compressed area (inside of bend) to the area in tension (outside of bend). If these compressive stresses cannot be relieved rapidly by internal migration of plasticizer, then plasticizer will spew. The internal migration of plasticizer will continue and when a deficiency of plasticizer occurs at the compressed area spewed plasticizer will be reabsorbed. It is possible for certain plasticizers to spew and be reabsorbed quite rapidly. Less compatible plasticizers are capable of spewing early and continuing to spew throughout the test. A test of one week's duration is used for screening, while an extended test of seven weeks' duration is used for a complete profile. Note 3: It is permissible for the seller and the purchaser to
agree upon other test conditions of time, temperature, or relative
humidity.
|
||||
| 1. Scope | ||||
|
1.1 This practice determines the compatibility of plasticizers in poly(vinyl chloride) plastics by rating the amount of plasticizer that spews due to compressional stress set up inside a 180° loop bend. Note 1: Ingredients other than plasticizer can spew from a
total formulation.
1.2 The text of this practice references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this practice. 1.3 The values as stated in SI units are to be regarded as the standard. The values in parentheses are given for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2: There is no known ISO equivalent to this
standard.
|
||||
| 2. Referenced Documents | ||||
|
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
