Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D3032-16

Standard Test Methods for Hookup Wire Insulation

NORMA vydaná dňa 1.11.2016

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 109.20 € Tlačené - 109.20 €
Dostupnosť	SKLADOM
Cena	109.20 € bez DPH
109.20 €

Informácie o norme:

Označenie normy: ASTM D3032-16
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2016
Kód tovaru: NS-668468
Počet strán: 41
Približná hmotnosť: 123 g (0.27 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Elektrické dráty

Anotácia textu normy ASTM D3032-16 :

Keywords:
ambient temperature, arcing, arc-propagation, arc-tracking, atmospheric pressure, breakdown voltage, cable, circuit breakers, current limiting, cuts, degradation, dropping apparatus, dry-arcing, electrical insulation, electrolyte, extinction voltage, flame propagation, flame spread, flame test, flammability, hookup wire, insulation thickness, moisture, open-circuit detection, partial discharge, power supply, safe voltage, scintillation, service condition, short-circuit detection

Doplňujúce informácie

1. Scope

1.1 These test methods cover procedures for testing hookup wire.

1.2 For the purposes of these test methods, hookup wire insulation includes all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions.

1.3 The test procedures and their locations are as follows:

Section

Axial Stability (Longitudinal Change) After Thermal Exposure

Bondability of Insulation to Potting Compounds

Capacitance

9 to 12

Cold Bend Test

Concentricity

Crush Resistance

Dielectric Breakdown Voltage

Dimensions

Dry-Arc Tracking

Dynamic Cut-Through

Fluid Immersion

High Temperature Shock

Insulation-Continuity Proof Tests

Insulation Resistance

Partial Discharge (Corona) Inception and Extinction Voltage

Relative Thermal Life and Temperature Index

Strip Force

Surface Resistance

Tensile Properties

Vertical Flame Test

Voltage Rating of Hook-Up Wire

Voltage Withstand Test

Wet Arc-Tracking

1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precaution statements, see 12.2.1, 12.4.1.8, 18.1.3, Note 17, and 25.4.

2. Referenced Documents

Standard101	Statistical Analysis of Thermal Life Test Data
Federal Specification	for Tape, Gummed; Paper, Reinforced and Plain, for Sealing and Securing (PPP-T-45C) Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
D5032-19	Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E691-23	Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
Standard98	Guide for the Preparation of Test Procedures for the Thermal Evaluation of Electrical Insulating Materials
D2303-20e1	Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials (Includes all amendments and changes 5/5/2021).
D2307-21	Standard Test Method for Thermal Endurance of Film-Insulated Round Magnet Wire
D2865-01	Standard Practice for Calibration of Standards and Equipment for Electrical Insulating Materials Testing
D3183-10(2019)	Standard Practice for Rubber´Preparation of Pieces for Test Purposes from Products
D3636-19	Standard Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials
D3638-21e1	Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials (Includes all amendments and changes 2/2/2022).
D5374-22a	Standard Test Methods for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation (Includes all amendments and changes 10/4/2022).
D5423-23	Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
D6054-97	Standard Practice for Conditioning Electrical Insulating Materials for Testing
D149-20	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D150-22	Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
D257-14(2021)e1	Standard Test Methods for DC Resistance or Conductance of Insulating Materials (Includes all amendments and changes 5/6/2021).
D374-99	Standard Test Methods for Thickness of Solid Electrical Insulation
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D471-16a(2021)	Standard Test Method for Rubber Property—Effect of Liquids (Includes all amendments and changes 6/25/2021).
D543-21	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D638-22	Standard Test Method for Tensile Properties of Plastics
D1711-24	Standard Terminology Relating to Electrical Insulation
D1868-20	Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems

Doporučujeme: