Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D2978-15e1
Standard Test Methods for Volume of Processed Peat Materials (Includes all amendments And changes 7/12/2023).
NORMA vydaná dňa 1.5.2015
Informácie o norme:
Označenie normy: ASTM D2978-15e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2015
Kód tovaru: NS-845265
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D2978-15e1 :
Keywords:
peat, volume, volume measurement,, ICS Number Code 65.080 (Fertilizers)
Doplňujúce informácie
| Significance and Use | ||||||||
|
5.1 These test methods are used to quantify the volume of peats under consideration in commercial transactions to determine if the package contains the labeled quantity. As such, material comes into the test area in an “as sold” condition. Note 1: The quality of the result produced by this standard is
dependent on the competence of the personnel performing it, and the
suitability of the equipment and facilities used. Agencies that
meet the criteria of Practice D3740 are generally considered capable of
competent and objective testing/sampling/inspection/etc. Users of
this standard are cautioned that compliance with Practice
D3740 does not in itself
ensure reliable results. Reliable results depend on many factors;
Practice D3740 provides a
means of evaluating some of those factors.
|
||||||||
| 1. Scope | ||||||||
|
1.1 These test methods cover the measurement of the volume of loose and baled processed peat expressed as cubic feet and is used as a quality control measurement to determine if the package contains the labeled amount of material. The results of these test methods are highly dependent on the experience of the personnel running the procedure. 1.2 There are two test methods, Method A for Loose Peat and Method B for Baled Peat. Method A is used when the material is uncompacted and Method B is used when the material is compacted. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. Except, that the sieve designations are typically identified using the “alternative” system in accordance with Practice E11, such as 3-in. and No. 200, instead of the “standard” of 75-mm and 75-µm, respectively. 1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.4.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||
| 2. Referenced Documents | ||||||||
|
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
