Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D1710-15
Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes
Automaticky preložený názov:
Štandardné špecifikácie pre lisovanú polytetrafluóretylénu ( PTFE ) Rod , hrubostenných potrubia a základných tvarov
NORMA vydaná dňa 1.9.2015
Informácie o norme:
Označenie normy: ASTM D1710-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2015
Kód tovaru: NS-615024
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D1710-15 :
Keywords:
fluorocarbon polymer, fluoropolymers, granular PTFE, polytetrafluoroethylene, PTFE, PTFE heavy-walled tubing, PTFE rod,, ICS Number Code 83.140.99 (Other rubber and plastic products)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||
|
1.1 This specification covers extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D4894 and reprocessed PTFE resin (as defined in Guide D7209). 1.2 The specification covers all sizes of rod, tubing, and basic shapes with a wall thickness of 1.6 mm (1/16 in.) or greater. These materials must be made wholly from PTFE and produced in accordance with good commercial ram extrusion practices. Note 1: This specification and ISO/DIS 13000-1 (1997) and
ISO/DIS 13000-2 (1997) differ in approach, however, data obtained
using either are technically equivalent.
Note 2: For compression molded PTFE materials, see
Specification D3294. Material
that can be certified to Specification D3294 may be substituted for
Specification D1710, however
the reverse in not true.
1.3 The values stated in SI units, as detailed in IEEE/ASTM SI 10 are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only. 1.4 The following precautionary caveat pertains to
the test methods portion, Section 12, only of this specification:
Standard Test Method for Dielectric
Breakdown Voltage and Dielectric Strength of Solid Electrical
Insulating Materials at Commercial Power Frequencies IEEE/ASTM SI 10 Standard for the Use of the International
System of Units (SI): The Modern Metric System Available from ASTM
International, 100 Barr Harbor Drive, West Conshohocken, PA
19428. Standard Test Methods for Physical
Dimensions of Solid Plastics Specimens Standard Specification for
Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion
Materials Standard Practice for Packaging/Packing
of Plastics Standard Test Methods for Density and
Specific Gravity (Relative Density) of Plastics by Displacement Standard Practice for Conditioning
Plastics for Testing Standard Test Methods for Thickness of
Solid Electrical Insulation Standard Guide for Writing Material
Standards in the Classification D4000 Format Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) Standard Terminology Relating to
Plastics Standard Guide for Radiographic
Examination ISO 13000-2 (2005) PlasticsPolytetrafluoroethylene (PTFE)
Semi-Finished Products, Part 2: Preparation of Test Specimen and
Determination of Properties ISO 13000-1 (2005) PlasticsPolytetrafluoroethylene (PTFE)
Semi-Finished Products, Part 1: Basis for Specification Standard Guide for Waste Reduction,
Resource Recovery, and Use of Recycled Polymeric Materials and
Products (Withdrawn 2015) |
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
