Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D1234-13

Standard Test Method of Sampling and Testing Staple Length of Grease Wool (Withdrawn 2022)

Automaticky preložený názov:

Štandardná skúšobná metóda pre odber vzoriek a testovanie Staple Dĺžka Grease vlny

NORMA vydaná dňa 1.7.2013

Jazyk
Prevedenie	Elektronické PDF - 60.70 € Tlačené - 60.70 €
Dostupnosť	SKLADOM
Cena	60.70 € bez DPH
60.70 €

Informácie o norme:

Označenie normy: ASTM D1234-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2013
Kód tovaru: NS-16710
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Přírodní vlákna

Anotácia textu normy ASTM D1234-13 :

Keywords:
length, sampling, statistics, wool, ICS Number Code 59.060.10 (Natural fibres)

Doplňujúce informácie

Significance and Use

5.1 The testing procedure in this test method for the determination of staple length is considered satisfactory for acceptance testing of commercial shipments of grease wool since the test method has been used in the trade for acceptance testing.

5.1.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.

5.2 The test method is used for the determination of the average unstretched staple length and the staple length distribution of a lot of wool in order to assign length classes when determining the conformance of lots and shipments to length specifications.

5.3 In this test method, the size of a lot covered by the test procedure is limited to not more than 200 packages per test. Any shipment exceeding the above limits is divided into lots within the prescribed limits.

5.4 The nature of the sampling procedure is such that grease wool staples as originally drawn from the wool of the lot require only a slight amount of preparation before measurement. The bulk and laboratory samples are synonymous in this test method.

5.5 Compression of wool in the bale makes it difficult to penetrate the interior of the bale with the sampling tool. However, staples can be drawn from the surface of the bale with the sampling tool or by hand.

5.6 Practice D4271 contains information on how to write a section on sampling in test methods.

1.1 This test method² covers procedures for sampling and measuring the unstretched staple length, and variability in length, of grease or pulled wool staples. The test method is also applicable to mohair and other animal fibers in staple form. The procedure is not recommended for individual fibers or groups of straightened fibers.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D4845-10(2018)	Standard Terminology Relating to Wool
D519-04	Standard Test Method for Length of Fiber in Wool Top
D1575-13	Standard Test Method for Fiber Length of Wool in Scoured Wool and in Card Sliver (Withdrawn 2022)
D123-23	Standard Terminology Relating to Textiles
D4271-88(2001)	Standard Practice for Writing Statements on Sampling in Test Methods for Textiles (Withdrawn 2009)