Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Norma ASTM B901-04(2021) 1.2.2021 náhľad

Doplňujúce informácie

ASTM B901-04(2021)

Standard Specification for Compressed Round Stranded Aluminum Conductors Using Single Input Wire Construction

NORMA vydaná dňa 1.2.2021

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 58.10 € Tlačené - 58.10 €
Dostupnosť	SKLADOM
Cena	58.10 € bez DPH
58.10 €

Informácie o norme:

Označenie normy: ASTM B901-04(2021)
Dátum vydania normy: 1.2.2021
Kód tovaru: NS-1018212
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Elektrická rozvodná vedení

Anotácia textu normy ASTM B901-04(2021) :

This specification covers aluminum 1350-H19, 1350-H16 or -H26, 1350-H14 or -H24, 1350-H142 or -H242, and aluminum alloy 8XXX series for tempers ""O"" and H1X or H2X, bare stranded conductors composed of one or more roller shaped or die compressed layers of helically laid wires. The conductors are for general use for electrical purposes. The conductors described in this specification are intended for subsequent insulation or covering. The areas of cross section, the minimum number of wires, and diameters of the finished strand shall conform to the prescribed construction requirements. The rated strength of 1350-H19 conductors shall be taken as the percent of the sum of the strengths of the component wires, calculated using the nominal wire diameters and the specified minimum average tensile strength. The rated strength of 800 series conductors shall be taken as the percent of the sum of strengths of the component wires, calculated using nominal wire diameters and the specified minimum average tensile strength. The approximate mass and electrical resistance may be determined using the standard increments due to stranding. Mechanical and electrical tests shall be made for not annealed and annealed conductors after stranding. Temperature correction factors for conductor resistance shall be provided when dc resistance is measured at specified temperatures.

Keywords:
aluminum, aluminum stranded conductors, compressed, concentric lay stranded conductors, electrical conductors, reverse concentric, single input wire, SIW, unidirectional, unilay,, ICS Number Code 29.240.20 (Power transmission and distribution lines)

Doplňujúce informácie

1. Scope

1.1?This specification covers aluminum 1350-H19 (extra hard), 1350-H16 or -H26 (³/₄?hard), 1350-H14 or -H24 (¹/₂?hard), 1350-H142 or -H242 (¹/₂?hard), and aluminum alloy 8XXX series as listed in Specification B800 for tempers O and H1X or H2X, bare stranded conductors composed of one or more roller shaped or die compressed layers of helically layed wires. The conductors are for general use for electrical purposes (Explanatory Notes 1 and 2).

Note 1:?For the purposes of this specification, single input wire (SIW) construction is defined as follows: a stranded conductor design methodology that varies the number of wires within a range of conductor sizes in order to permit that range of conductor sizes to be constructed from a single wire size.

1.2?The SI values for resistivity are regarded as standard. For all other properties, the inch-pound units are regarded as standard and the SI units may be approximate.

Note 2:?Prior to 1975, aluminum 1350 was designated as EC aluminum.

Note 3:?The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to Unified Numbering System A91350 in accordance with Practice E527. Aluminum alloys in the 8000 series correspond to Unified Numbering System A98XXX in accordance with Practice E527.

Note 4:?This specification also permits conductors for use as covered or insulated electrical conductors.

Note 5:?Sealed conductors, which are intended to prevent longitudinal water propagation and are further covered/insulated, are also permitted within the guidelines of this specification.

1.3?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

NBS Handbook 100	Copper Wire Tables Available from National Technical Information Service (NTIS), 5301 Shawnee Rd., Alexandria, VA 22312, http://www.ntis.gov.
B193-20	Standard Test Method for Resistivity of Electrical Conductor Materials
B230/B230M-22	Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes
B263-04	Standard Test Method for Determination of Cross-Sectional Area of Stranded Conductors
B354-23	Standard Terminology Relating to Uninsulated Metallic Electrical Conductors
B609/B609M-12(2021)	Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes
B800-05(2021)	Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes—Annealed and Intermediate Tempers
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ANSI H35.1	American National Standard Alloy and Temper Designation System for Aluminum Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
B801-18(2023)	Standard Specification for Concentric-Lay-Stranded Conductors of 8000 Series Aluminum Alloy for Subsequent Covering or Insulation

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.