Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM B701/B701M-13(2018)
Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD)
NORMA vydaná dňa 1.3.2018
Informácie o norme:
Označenie normy: ASTM B701/B701M-13(2018)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2018
Kód tovaru: NS-810001
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM B701/B701M-13(2018) :
Keywords:
aluminum electrical conductors, concentric-lay stranded aluminum conductors, concentric-lay stranded aluminum conductors, steel-reinforced, concentric-lay stranded self-damping aluminum conductors, steel reinforced, electrical conductors, electrical conductors´aluminum, self-damping conductors, steel reinforced stranded aluminum conductors, stranded aluminum conductors,, ICS Number Code 29.240.20 (Power transmission and distribution lines)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||
|
1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor, steel-reinforced (ACSR/SD), and its component wires for use as overhead electrical conductors (Explanatory Notes 1 and 2). 1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. For conductor sizes designated by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units. 1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard. Note 1: ACSR/SD is designed to control aeolian vibration by
integral damping. The conductors consist of a central core of a
round steel wire or wires surrounded by two layers of trapezoidal
aluminum 1350-H19 wires or two layers of trapezoidal aluminum
1350-H19 wires and one layer of round aluminum 1350-H19 wires
(Fig. 1). The
trapezoidal-wire layers are separated from each other and from the
steel core by two small annular gaps that provide the conductors
self-damping characteristics. The round aluminum wires are in tight
layer contact between themselves and the underlying trapezoidal
wire layer. Different strandings of the same size of conductor are
identified by type, which is the approximate ratio of steel area to
aluminum area, expressed in percent (Table 1 and Table 2).
FIG. 1 Illustrations of Typical ACSR/SD Strandings Note 2: The aluminum and temper designations conform to ANSI
Standard H 35.1. Aluminum 1350 corresponds to UNS A91350 in
accordance with Practice E527.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||
|
Odporúčame:
EviZak - všetky zákony vrátane ich evidencie na jednom mieste
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
