Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM B22/B22M-17
Standard Specification for Bronze Castings for Bridges and Turntables
NORMA vydaná dňa 1.4.2017
Informácie o norme:
Označenie normy: ASTM B22/B22M-17
Dátum vydania normy: 1.4.2017
Kód tovaru: NS-682304
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM B22/B22M-17 :
This specification covers the requirements for UNS C86300, C90500, C91100, C91300, or C93700 bronze alloy castings for turntables, movable bridges, and bridge parts. This specification also includes bronze castings made from the same copper alloys that are suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. Each product should be manufactured by casting to produce a uniform finished product. Castings made from the UNS C86300 copper alloy should be subjected to Brinell hardness, tension, and compression tests while those made from UNS C91100 and C91300 should be subjected to compression tests. UNS C90500 copper alloy castings should undergo tension tests. All mechanical properties like deformation limit in compression, hardness, and yield strength are determined from separately cast test bars and should conform to the specified requirements.
Keywords:
bridge plates, bronze castings, copper-alloy castings, copper-base alloy castings, expansion bearings, UNS No. C86300, UNS No. C90500, UNS No. C91100, UNS No. C91300, UNS No. C93700,, ICS Number Code 77.150.30 (Copper products)
Doplňujúce informácie
| 1. Scope | ||||||||||||
|
1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700. Note 1: Historically, the alloys in this specification have
been used in the applications listed in Appendix X1. Actual practice may
vary.1.2 The values stated in either SI units
or inch-pound units are to be regarded separately as standard.
Within the text, SI units are shown in brackets. The values stated
in each system may not be exact equivalents; therefore, each system
shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
