Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM A1055/A1055M-16 1.12.2016 náhľad

Doplňujúce informácie

ASTM A1055/A1055M-16

Standard Specification for Zinc and Epoxy Dual-Coated Steel Reinforcing Bars

NORMA vydaná dňa 1.12.2016

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.00 € Tlačené - 70.00 €
Dostupnosť	SKLADOM
Cena	70.00 € bez DPH
70.00 €

Informácie o norme:

Označenie normy: ASTM A1055/A1055M-16
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2016
Kód tovaru: NS-677496
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Kovové povlaky
Organické povlaky

Anotácia textu normy ASTM A1055/A1055M-16 :

Keywords:
coating requirements, concrete reinforcement, continuous hot-dip galvanized, corrosion resistance, dual coated, epoxy coating, galvanizing, steel bars, thermal spray coating (metallization), zinc-alloy coating,, ICS Number Code 25.220.40 (Metallic coatings),25.220.60 (Organic coatings)

Doplňujúce informácie

1. Scope

1.1 This specification covers deformed and plain steel reinforcing bars with a dual coating of zinc-alloy followed by an epoxy coating applied by the electrostatic spray method.

1.2 The zinc-alloy coating is produced as one of two types: zinc-alloy applied by the thermal spray method (Type I) or zinc-alloy applied in accordance with Specification A1094/A1094M (Type II).

Note 1: The coating applicator is identified throughout this specification as the manufacturer.

1.3 Requirements for the zinc coating are contained in
Table 1.

1.4 Requirements for epoxy powder coatings are contained in Annex A1.

1.5 Guidelines for construction practices at the job-site are presented in Appendix X1.

1.6 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.7 This specification is applicable for orders in either inch-pound units [as Specification A1055] or SI units [as Specification A1055M].

1.8 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, except as specifically noted in Table 2. Combining values from the two systems may result in non-conformance with this specification.

1.9 This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

G20-10(2019)	Standard Test Method for Chemical Resistance of Pipeline Coatings
B117-19	Standard Practice for Operating Salt Spray (Fog) Apparatus
G8-24	Standard Test Methods for Cathodic Disbonding of Coated Steel
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
D4060-19	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
B833-20	Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
A944-22	Standard Test Method for Comparing Bond Strength of Steel Reinforcing Bars to Concrete Using Beam-End Specimens
Voluntary Certification Program	for Fusion Bonded Epoxy Coating Applicator Plants
ACI 301	Specifications for Structural Concrete
A706/A706M-22a	Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement (Includes all amendments and changes 2/22/2023).
A615/A615M-22	Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
SSPC-VIS 1	Pictorial Surface Preparation standards for Painting Steel Surfaces
RP-287	Field Measurement of Surface Profile of Abrasive Blast-Cleaned Steel Surface Using a Replica Tape
AWS C2.25/C2.25M	Specification for Thermal Spray Feedstock--Solid and Composite Wire and Ceramic Rods
G62-23	Standard Test Methods for Holiday Detection of Coatings used to Protect Pipelines
A996/A996M-16	Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement
G14-04(2018)	Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.